Vali riik saadetise kohaletoimetamiseks

RockBoard RBO B QM T J1 Paigalduskomplekt

Tootekood: 1338212

RockBoard RBO B QM T J1 Paigalduskomplekt

Tootekood: 1338212

The RockBoard QuickMount Type J1 is a screw-on pedal mounting plate that locks BOSS DD-500, MD-500, RV-500, and STRYMON BigSky, Mobius, and TimeLine pedals into the RockBoard Slot Grid without hook-and-loop tape. The flat carbon-reinforced composite plastic plate measures 171 × 129 mm and ships with replacement screws for a clean, residue-free…

RockBoard RBO B QM T J1 Paigalduskomplekt

The RockBoard QuickMount Type J1 is a screw-on pedal mounting plate that locks BOSS DD-500, MD-500, RV-500, and STRYMON BigSky, Mobius, and TimeLine pedals into the RockBoard Slot Grid without hook-and-loop tape. The flat carbon-reinforced composite plastic plate measures 171 × 129 mm and ships with replacement screws for a clean, residue-free install on top of the pedal's existing back plate.

  • Compatibility: BOSS DD-500, MD-500, RV-500, STRYMON BigSky, Mobius, TimeLine — flagship delay, modulation and reverb units
  • Plate dimensions: 171 × 129 mm — flat surface that sits flush against the pedal's back plate
  • Material: carbon-reinforced composite plastic — light, stiff, and road-tough
  • Mounting: replacement screws included — uses original pedal back-plate holes, no drilling required
Täpsem kirjeldus sinu emakeeles ei ole veel saadaval. Abiks võib olla ingliskeelne kirjeldus.

Pedal Mounting Plate for RockBoard Slot Grid Pedalboards

The RockBoard QuickMount Type J1 anchors BOSS DD-500, MD-500, RV-500, and STRYMON BigSky, Mobius, and TimeLine pedals into any RockBoard pedalboard with a Slot Grid. The screw-on plate replaces dust-collecting hook-and-loop tape, attaching directly to the pedal's existing mounting holes. Once installed, it clicks into the Slot Grid and holds the pedal firmly during transport and live performance.

What Sets the QuickMount Type J1 Apart

Designed for the wider housings of flagship BOSS 500-series and STRYMON TimeLine-family pedals, the Type J1 is one of the larger plates in the QuickMount range. Carbon-reinforced composite plastic keeps weight low while staying rigid enough for repeated load-ins, and mounting on top of the existing back plate leaves no sticky residue on either the pedal or the board.

Pedal Compatibility — Drop-In Fit for Flagship Units

Developed around the screw-hole pattern shared by BOSS 500-series processors and STRYMON's TimeLine, Mobius, and BigSky enclosures, this plate lets each supported pedal drop straight on with no modification.

  • Compatible pedals: BOSS DD-500, MD-500, RV-500, STRYMON BigSky, Mobius, TimeLine — delay, modulation and reverb units
  • Pedalboard fit: RockBoard Slot Grid — clicks into the board's universal mounting channel
  • Mounting method: screws onto existing pedal back plate — uses original or supplied replacement screws

Plate Dimensions and Construction

At 171 × 129 mm, the flat surface supports the larger housings of the BOSS 500-series and STRYMON flagship pedals without overhang. The carbon-reinforced composite plastic is light enough that adding it does not change the board's balance, yet stiff enough to resist flex under foot pressure.

  • Width: 171 mm — covers the full width of BOSS 500-series and STRYMON TimeLine-family housings
  • Depth: 129 mm
  • Material: carbon-reinforced composite plastic — rigid, lightweight, and resistant to flex under foot pressure

What's in the Box and How It Installs

Replacement mounting screws ship with the plate, so the install can be completed even if the original pedal screws are lost. Because it sits on top of the existing back plate, swapping a pedal between boards is a matter of unclipping it from the Slot Grid — no residue, no drilling, no permanent changes.

  • Package contents: mounting plate and replacement screws — pedal and pedalboard sold separately
  • Installation: no permanent modifications required — uses the pedal's existing screw holes
  • Removal: residue-free — leaves both the pedal back plate and the pedalboard surface clean

Sobivus
Material

Materjal

Plast

Pakend

Pakend sisaldab

Kruvid

Dimensions and Weight

Laius (mm)

171

Sügavus (mm)

129

Country

Päritoluriik

Hiina

Dokumendid

Kasutusjuhendid
Teave tootja kohta
Tootja:
Warwick GmbH & Co Music Equipment KG
Gewerbepark 46, 08258, Markneukirchen, Saksamaa
Vastutav isik:
Warwick GmbH & Co Music Equipment KG
Ohutusjuhised

Selle toote spetsiifilised ohutusjuhised leiad kasutusjuhendist.