cookies
You will find our "cookies" delicious
The purpose of the cookies of the Muziker website is to make your visit to us a pleasant experience at all times. Consent to the use of all cookies by clicking the "I agree" button, or in the settings select only the ones you like. More information.
Sale has ended

Amptweaker DepthFinder

2 Band active Boost-only EQ. Add Resonance and Presence to the effects loop or pedalboard with the DepthFinder active EQ. One of the key ingredients to tube amplifier tone is the fact that their power amps have much lower damping factors than...
Sale has ended
This product is no longer being manufactured or is not part of our offer anymore. We recommend choosing an alternative product.
Choose an alternative (3)
Guitar Effect Amptweaker DepthFinder

Amptweaker DepthFinder

Choose an alternative (3)

Product code: AT-DEPTHFINDER | ID: 289384

Amptweaker DepthFinder

2 Band active Boost-only EQ. Add Resonance and Presence to the effects loop or pedalboard with the DepthFinder active EQ. One of the key ingredients to tube amplifier tone is the fact that their power amps have much lower damping factors than their solid state or digital counterparts. Vintage tube amps used the Presence control to adjust the damping at high frequencies, to boost the extreme high end and make the sound more lively. In the 1990’s, the 5150 amp added a Resonance control, which deploys the same technique in the lowend, boosting the bottom where the speaker and cabinet resonance happened to be, to allow the user to tailor that for his preferred tightness…. especially noticeable when palm-muting and stopping notes. Now many tube amps have these type of controls, but rarely do solid state amps include this…. . and the result is that the solid state amps can sound TOO tight. The DepthFinder is an active boost-only EQ pedal that simulates the tube amp Resonance and Presence controls, but without having to be done in the power amp. This means you can use it with an amp that doesn’t have Resonance and Presence, by patching it in the effects loop. It also works great for building a pedalboard direct signal, since that low damping factor is a key ingredient to the overall tone. It can easily make a solid state amp sound and feel more like a tube amp, and can actually widen the bandwidth since it boosts at very low and very high frequencies. The frequency range and boost of each knob was matched to the controls on the 5150, while the amp was connected to a Vintage 30-loaded birch plywood cabinet, so the resonance matches that resonant system. The Presence also matches how the amp reacts to the inductance of the speakers. The taper of the pots were also improved, so that it’s easier to find the sweet spot of each! The pedal has a high impedance input, so it can be used in front of the amp with a guitar into it, but the best simulation of power amp damping EQ comes from putting it further down the line, such as in the amp’s effects loop. If no loop exists, use it after all distortion for the best results. If using it in an amp’s effects loop, make sure not to place it above the power transformer end of the amp(usually near the power switch and line cord), otherwise it and the cables could pick up hum. When using the DepthFinder in an Amptweaker pedal loop, you will normally get better results by setting that loop to Post…. . but it could be used in front to add brilliance and/or punchy bottom to the guitar tone. It can also be used to add more sizzle or punch to the Boost loops on the Pro pedals, to help the solo cut through, or just to make a heavier tone with the extra gain. The DepthFinder is a simple way to tweak your pedal yourself. And lastly, it can help simulate a typical tube clean tone if used in the SideTrak loop so it only affects the clean tone. The DepthFinder can also be used with any pedalboard looper system, allowing it to be added into the pedalboard for certain presets that need to be more lively or punchy sounding. Specifications: Resonance and Presence controls simulate power amp damping EQ, Inside gain boost trimpot, Can be used in amp effects loop or pedalboard, Power Supply: 4mA with 9V or 18V supply (not included), Weight: 6 ounces, Dimensions: 3. 7″W X 1. 5″D X 2″H

Parameters and specifications

Suitability

Power supply

Power Supply


Accessory

UK/EU Power supply included

No


Country

Made in

USA


Recommended accessories